¡@

PATCHCORD INTRODUCTION PATCHCORD ¡@ Mastercord ¡@ Patchcord/Pigtail ¡@ Fan out Patchcord CABLES ¡@ Singlemode ¡@ Multimode ¡@ LSZH/PVC CONNECTOR ¡@ DIN Connector ¡@ SC Connector ¡@ ST Connector ¡@ FC Connector ¡@ LC Connector ¡@ MT-RJ Connector ¡@ MPO Connector ¡@ MU Connector ADAPTOR ¡@ ST Adaptor ¡@ SCPC / SC APC Adaptor ¡@ FC Adaptor ¡@ LCPC / LC APC Adaptor ¡@ MTRJ Adaptor ¡@ MPO/MTP Adaptor ¡@ MU Adaptor ATTENUATOR ¡@ Fixed Attenuator CONNECTOR / FC Connector FC/APC 2.0 Singlemode Features: Only used with singlemode fiber requiring high return loss performance. Pre-radiused and 8 degree pre-angled ceramic ferrule. Suitable for use with two part heat curing epoxies and cold cure anaerobic adhensives. Available with either 900um boots for pigtail termination or 3.0mm crimp ring and boot for patchcord production. Typical insertion loss<0.25db. Return loss of 60db min. ¡@ OD 0.9 Multi Mode Features: Normally used for singlemode fibre, but multimode also available. Optically and mechanically compatible with all other FC/PC connectors. One piece design features pre-radiused ceramic ferrule Suitable for use with two part heat curing epoxies and cold cure anaerobic adhensives. Available with either 900um boots for pigtail termination or 3.0mm crimp ring and boot for patchcord production. Typical singlemode insertion loss<0.2db. ¡@ OD 2.0 Multi Mode Features: Normally used for singlemode fibre, but multimode also available. Optically and mechanically compatible with all other FC/PC connectors. One piece design features pre-radiused ceramic ferrule Suitable for use with two part heat curing epoxies and cold cure anaerobic adhensives. Available with either 900um boots for pigtail termination or 3.0mm crimp ring and boot for patchcord production. Typical singlemode insertion loss<0.2db. ¡@ OD 3.0 Multi Mode Features: Normally used for singlemode fibre, but multimode also available. Optically and mechanically compatible with all other FC/PC connectors. One piece design features pre-radiused ceramic ferrule Suitable for use with two part heat curing epoxies and cold cure anaerobic adhensives. Available with either 900um boots for pigtail termination or 3.0mm crimp ring and boot for patchcord production. Typical singlemode insertion loss<0.2db. ¡@ OD 0.9 Single Mode Features: Normally used for singlemode fibre, but multimode also available. Optically and mechanically compatible with all other FC/PC connectors. One piece design features pre-radiused ceramic ferrule Suitable for use with two part heat curing epoxies and cold cure anaerobic adhensives. Available with either 900um boots for pigtail termination or 3.0mm crimp ring and boot for patchcord production. Typical singlemode insertion loss<0.2db. ¡@ OD 2.0 Single Mode Features: Normally used for singlemode fibre, but multimode also available. Optically and mechanically compatible with all other FC/PC connectors. One piece design features pre-radiused ceramic ferrule Suitable for use with two part heat curing epoxies and cold cure anaerobic adhensives. Available with either 900um boots for pigtail termination or 3.0mm crimp ring and boot for patchcord production. Typical singlemode insertion loss<0.2db. ¡@ OD 3.0 Single Mode Features: Normally used for singlemode fibre, but multimode also available. Optically and mechanically compatible with all other FC/PC connectors. One piece design features pre-radiused ceramic ferrule Suitable for use with two part heat curing epoxies and cold cure anaerobic adhensives. Available with either 900um boots for pigtail termination or 3.0mm crimp ring and boot for patchcord production. Typical singlemode insertion loss<0.2db. ¡@ ¡@ ¡@